Automation/Robot Specialist

· Perform scheduled preventive maintenance on robots, PLCs, conveyors, vision systems, servo systems, pneumatics, electrical devices, and related automation components in accordance with standardized procedures. 

· Serve as the first responder for automation failures; diagnose electrical, mechanical, controls, robotic, network, and process-related faults and restore equipment safely with minimal production impact. 

· Monitor equipment condition and identify wear, abnormal noise, degraded performance, and other early failure indicators before breakdowns occur. 

· Complete equipment inspections, adjustments, component replacements, backups, calibrations, and functional checks within the technician’s authorized scope. 

· Record work performed, parts used, downtime, corrective actions, and failure modes in the computerized maintenance management system (CMMS). 

· Escalate complex or recurring issues to Automation Engineering or the Automation Specialist with clear diagnostic evidence and recommended follow-up actions. 

· Support root-cause analysis and reliability improvement activities by identifying repeat failures and providing accurate maintenance history. 

· Train and coach production operators on safe, basic automation troubleshooting and proper escalation practices. 

· Follow all applicable safety procedures, including lockout/tagout, electrical safety, robot safety, and emergency-stop validation. 

· Complete 100% of assigned preventive maintenance tasks on time. 

· Respond promptly to downtime events, with a target initial response of less than 15 minutes. 

· Reduce mean time to repair and improve equipment recovery time. 

· Minimize repeat failures by identifying chronic issues and supporting permanent corrective actions. 

· Maintain accurate, timely maintenance records and communicate emerging reliability risks clearly. 

· Rockwell PLC and HMI systems: Intermediate troubleshooting and basic authorized modifications using Studio 5000, FactoryTalk View, and RSLinx. Must be able to read ladder logic; monitor tags and I/O; perform basic online edits such as timer values and counter presets; use approved I/O forcing practices; interpret fault codes; troubleshoot I/O modules; verify communications; and use trends and force tables. 

· FANUC robots and collaborative robots: Operational troubleshooting, basic teach-pendant programming, position teaching, simple motion edits, I/O verification, program backup and restoration, position-register changes, alarm interpretation, servo fault diagnosis, mastering and calibration verification, battery replacement, lubrication, cable inspection, end-of-arm tooling troubleshooting, hand-guiding, safety-zone verification, and collision-sensitivity adjustment. 

· Vision systems: Basic setup and troubleshooting of Keyence and Cognex systems, including job or scene selection, lighting, focus, exposure, image review, pass/fail thresholds, basic inspection-tool parameters, camera positioning, lens maintenance, and communication verification. 

· Mechanical and pneumatic systems: Troubleshooting and adjustment of cylinders, valves, air-pressure controls, conveyors, belt tracking, motors, sensors, and related mechanical components. 

· Electrical and servo systems: Safe use of a multimeter for voltage, continuity, and resistance testing; sensor replacement and wiring verification; emergency-stop circuit testing; and basic Kinetix drive, encoder, and servo-system diagnostics. 

· Industrial networks: Basic EtherNet/IP diagnostics, device-presence and IP-address verification, switch-indicator review, ping testing, cable continuity testing, and connector inspection. 

· High school diploma or equivalent required; technical certification or associate degree in industrial maintenance, automation, mechatronics, electrical technology, or a related field preferred. 

· Three or more years of industrial maintenance experience supporting automated manufacturing equipment. 

· Demonstrated mechanical aptitude, structured troubleshooting ability, and capacity to read electrical schematics, wiring diagrams, mechanical drawings, and P&IDs. 

· FANUC Handling Tool Operations training required. 

· OSHA 10-Hour General Industry training required. 

· Lockout/Tagout Authorized Employee qualification required. 

· NFPA 70E arc-flash safety awareness required. 

· FANUC maintenance and collaborative robot safety training preferred. 

· Rockwell ControlLogix Maintenance and Troubleshooting (CCP253) and Studio 5000 Basic Operations training preferred. 

· Keyence CV-X Basic Operations and Cognex In-Sight Essentials training preferred. 

· Confined-space entry training required when applicable to the work area. 

· Working proficiency with a CMMS such as SAP PM, Maximo, or an equivalent system. 

· Basic proficiency with Microsoft Excel and Outlook for data logging, communication, and work-order support. 

· Ability to use tablets, smartphones, and approved mobile or augmented-reality tools for maintenance documentation and troubleshooting. 

Shifts: